Honda Countershaft Bearing 72mm Snap Ring 90601-PPP-000

Honda Countershaft Bearing 72mm Snap Ring – Genuine OEM (90601-PPP-000)

You’ve got the transmission open and a new countershaft bearing in your hand, so don’t go reusing the
old snap ring that was holding the last one in. This is that ring, Honda part 90601-PPP-000, the 72mm
one that locks your countershaft bearing (91004-PPP-014) down so it can’t wander around in the bore.
It’s a couple bucks and it weighs nothing, but it’s the difference between a bearing that stays put and
one that doesn’t. Since you’re already in there, grab the fresh one and do it right.

Don’t Reuse The Old One. Here’s Why.

Snap rings lose their grip every time you flex them on and off, and the one you’re about to pull has
been baking and getting loaded inside your transmission for years. It’s tired. Pop that worn ring back
in next to your shiny new bearing and you’re rolling the dice, maybe it holds, maybe it lets the
bearing creep, and a bearing that walks in its bore is the exact thing you tore the transmission down
to fix. You really want to button it all back up and find out the hard way? Didn’t think so. A new ring
snaps in with full tension and does its one job, and it costs less than your lunch. That’s about as
easy a call as you’ll make on this whole job.

It’s Sized For This Exact Bearing

This is the genuine Honda 72mm ring made for the 91004-PPP-014 countershaft bearing, so it drops right
into the groove with the fit and tension Honda spec’d for it. Could you grab something close from a
hardware store bin? Maybe, but “close” on diameter usually means wrong on thickness or material, and
inside a transmission that’s not where you want to be guessing. Get the right ring and you’re not
fighting it.

Grab The Bearing While You’re At It

If you’re buying this ring, you’re replacing the bearing it holds, so make sure you’ve got the91004-PPP-014countershaft bearing too. The two go together, and there’s nothing worse than having
everything torn apart and realizing you’re one little ring or one bearing short of finishing. Order
them at the same time and you’re set to knock the whole thing out in one go.

What You Get

• Genuine Honda countershaft bearing snap ring (90601-PPP-000)
• 72mm size, made for the 91004-PPP-014 countershaft bearing
• Retains the countershaft bearing in its bore
• Direct OEM replacement with the correct fit and tension
• Sold individually

Fits These Cars

• 2013-2015 Acura ILX
• 2002-2006 Acura RSX Base/Type S
• 2004-2014 Acura TSX
• 2003-2017 Honda Accord (K24)
• 2002-2015 Honda Civic Si
• 2016-2017 Honda Civic LX
• 2002-2006 Honda CR-V
• 2003-2010 Honda Element
• 2016-2018 Honda HR-V

Note: Genuine Honda countershaft bearing 72mm snap ring, part number 90601-PPP-000, which retains the
countershaft bearing (91004-PPP-014) in its bore. Sized specifically for that bearing for correct fit
and tension. It’s recommended any time you service the countershaft bearing, replace it rather than
reusing the original, since a used ring loses tension. Sold individually. Fits the 2013-2015 Acura ILX,
2002-2006 Acura RSX Base/Type S, 2004-2014 Acura TSX, 2003-2017 Honda Accord (K24), 2002-2015 Honda
Civic Si, 2016-2017 Honda Civic LX, 2002-2006 Honda CR-V, 2003-2010 Honda Element, and 2016-2018 Honda
HR-V. One snap ring per order.